chamfer
美 ['tʃæmfə(r)]英 ['tʃæmfə(r)]
- v.在…上雕槽[刻沟]；斜切；在…上挖圆槽
- n.斜切面；削角
- 网络倒角；倒直角；切角
复数：chamfers
chamferchamfer
倒角
CAD快捷命令大全 ... BR,*BREAK 打断 CHA,*CHAMFER 倒角 CO,*COPY 复制对象 ...
倒直角
怎样去学CAD啊？_爱问知识人 ... CH,*PROPERTIES 属性框 CHA,*CHAMFER 倒直角 DCO,*DIMCONTINUE 连续标注 ...
切角
CAD基础操作 - 永恒的日志 - 网易博客 ... 打断 break 切角 chamfer 倒角: fillet ...
倒斜角
实体建模_UG教程_沐风网 ... 03-23 ·螺纹- Modeling 03-23 ·倒斜角- chamfer 03-23 · 基准轴- Modeling Datum Axis ...
槽
专业术语汇集 - evagong-li的日志 - 网易博客 ... Centipoises 厘泊（粘度单位） Chamfer 倒棱，槽 Chamfered joint 斜削接 ...
倒角命令
倒角命令(Chamfer)——11-9(不适用于表面模型)n 二、倒圆角 n 圆角命令(Fillet)——11-8（不适用于表面模型） 三、三维阵列（…
倒棱
专业术语汇集 - evagong-li的日志 - 网易博客 ... Centipoises 厘泊（粘度单位） Chamfer 倒棱，槽 Chamfered joint 斜削接 ...
1
Two chamfer disk milling cutters are arranged on a chamfer main shaft, and are separated by a separating bush to determine spacing.
倒角主轴上装有两把倒角盘铣刀，通过隔套隔开并确定间距。
2
A milling hole main shaft, the chamfer main shaft and a main electric motor are all installed on a revolution body.
铣孔主轴、倒角主轴和主电机均安装在回转体上。
3
The length of chamfer shall be between1 and2 complete threads as measured parallel to the axis of the threaded component.
当平行于螺纹构件轴线方向进行测量时，倒角长度应该在1-2全螺纹扣之间。
4
Chamfer cap-there are all easy to wear, it is not easy out, and firmly strong and not easily lost or damaged.
柱帽体有倒角容易戴入，不易拔出、牢固性强、不易丢失和破损。
5
To create a smooth transition select edges along connection of the wall and the floor and apply Chamfer.
如果你要创建平滑的过渡，你可以沿着墙和地面交界的边，然后进行倒角。
6
A specially designed inner ring chamfer improves oil flow into the bearing for better lubrication and lower heat generation.
有特别设计的内环倒角提高石油流入轴承进行更好的润滑和低热量的产生。
7
CHAMFER : The flat surface formed by cutting away the sharp edges of two meeting surfaces.
倒角：两个表面相交处，通过切掉尖锐边缘形成的平面。
8
Diamond grade, thickness, chamfer, and or planar non-planar interface to your specifications.
金刚石的粒度、厚度、倒角及界面是否平面，可以根据用户要求确定。
9
Clean facial ministry to had better breed character with chamfer, let corneous layer become soft, blain blain is squeezed more easily piece.
清洗脸部最好用去角质乳，让角质层变得柔软，痘痘更轻易挤出。
10
rolling bearings . single - row angular contact ball bearings . chamfer dimensions for outer ring non - thrust side.
滚动轴承。单列角面接触的球轴承。外圈非推力边的倒圆角尺寸。
11
rolling bearings . single - row cylindrical roller bearings . chamfer dimensions for loose rib and non - rib sides.
滚动轴承。单列圆筒形滚子轴承。平挡圈和非凸缘边的倒圆角尺寸。
12
and the holding plate for fixing the chamfer to be processed is arranged on each bracket.
用来固定待加工弯头的夹持板设置在支架上。
13
A grinds arenaceous cream: Most all-pervading chamfer protects skin to taste with deep - seated cleanness character.
磨砂膏：最普及的去角质和深层清洁护肤品。
14
Objective: To observe the marginal fit on Ni-Cr alloy crown cemented on implant abutments with chamfer margin and shoulder margin.
目的：考察凹形龈缘和肩台龈缘种植体基桩的镍铬合金冠在粘接后的边缘适合性。
15
The specialized inspector inspects the bore diameter, pitch, chamfer and finish degree of bore wall.
加工完成后由专门检验员检验孔径、孔距、倒角大小、孔壁光洁度。
16
This circle along with the tooth tip circle (or start of chamfer circle) determines the limits of tooth profile requiring control.
渐开线终止圆与齿顶圆（或者修缘线的起点所在的圆）共同限制了所要求控制的渐开线齿廓的范围。
17
Oily skin can choose those who contain grain to grind arenaceous cream, fluid of qualitative water of tie-in chamfer, elite.
油性肌肤可以选择含颗粒的磨砂膏，并搭配去角质水、精华液。
18
Core drills. A core drill consists of the chamfer, body, neck, and shank, as shown in Fig. 12. 2.
空心钻包括斜面、钻头体、钻颈和钻柄，如图12.2所示。
19
But Brenda, I can't wait to get at her. . . And now this chamfer-blade wants sharpening.
但是，布伦达，我的美人儿，我可是急着要去见她……现在倒好，这块倒角刀片还得磨快点。
20
The utility model resolves the problem that existing full circle and chamfer tools are poor in full circle and chamfer effects.
它解决了现有整圆倒角工具整圆、倒角效果较差的问题。
21
Single type angle drills : Use to machine chamfer for hole of glass , stones etc . Various type and specification.
独立倒角钻头：用于玻璃孔、石材孔倒角使用。各种型号及规格。
22
The part of gradient coil near shell forms chamfer angle to lay more sound absorption material.
所述梯度线圈靠近外壳的部分形成倒角，以放入更多的吸声材料。
23
To ease installation it is recommended that the housing bore should have a lead-in or chamfer as shown in fig 3.
为便于安装，建议轴承座内孔应有一引导进入的倒角，如图3所示。
24
Extrude the edges in and chamfer the edges by 3 to get a smooth transition (Fig. 14).
向内挤压边线，然后切分出3断，以获得平滑的过渡。
25
The chamfer part of the chamfer drive sleeve [5] is meshed with the chamfer part of the driving wheel [4] after installation.
斜切传动套[5]斜切部分与传动轮[4]的斜切部分安装后相互啮合。
26
V rolling may decrease efficiently side overlap of plate, chamfer rolling may remove complately side overlap of plate.
平辊立轧可显著减小坯料侧面双鼓形及折叠，倒棱轧制可有效消除坯料侧面双鼓形。
27
If you need the capability study on the big chamfer for 300 pcs, then we have to measure at CMM(3D) as GFT method.
如果您需要300个大倒角能力的研究，那么我们在三坐标测量机（3D）测量GFT的方法。
28
RECHAMFER : Defect on radii and chamfer; defective chamfer such as nicks that are considered to be repairable.
重新倒角：可被重新修复的倒角缺陷，例如划痕。
29
But for Reminder: the dimensions related to big chamfer are not major characteristic.
但提醒：大倒角的尺寸并不大特点。
30
We the sale good number is multi-purpose the watch measures engine to embed in box of 3 chamfer lead plane.
咱们把发卖精采数字多用表测量引擎嵌入在3槽主机箱中。